|
Working
Environment |
 |
|
Temperature:10℃～35℃
Relative Humidity:
≤80﹪
Atmospheric Pressure:86kPa
～106kPa |
 |
|
Transport and Storage Environment |
|
Temperature:-10℃～40℃ Relative Humidity:≤80﹪
Atmospheric Pressure:50kPa～106kPa |
|
|
|
Power Supply Requirements |
|
Voltage: (single-phase) 220V±22V；20A
Frequency:50Hz±1Hz |
|
|
|
Display Function |
Display content：ECG waveform, Finger Pleth waveform,
inflation/deflation signal, SPO2,
pressure value, heart rate, NIBP, D/S ratio and
residual treatment time.
Scanning speed：25mm/s or 50mm/s. |
|
|
|
Operation Function |
|
Patient Protection |
◆The
System has following Functions
◆which
are ECG Amplitude
◆Finger
Pleth Amplitude
◆Inflation/Deflation
starting time Adjustment
◆Air
Pressure Adjustment
◆Treatment
Time Adjustment
◆Solenoid
Valve control
◆Compressor
Control
◆SPO2
Alarm, Blood Pressure Alarm
◆Patient
Information, and Printing. |
|
◆Automatic
inflation stop and pressure release on early
extra systole.
◆
Automatic pressure release whenever an extra
systole or other indicator of an
arrhythmia or aberrant activity is detected.
◆Automatic
treatment stop and pressure release if power
outage occurs.
◆Automatic
pressure release if air reservoir tank
pressure is more than 59kPa.
◆Automatic
high-pressure limit. Automatic release if
the pressure is 5 kPa over
setting.
◆Automatic
stop and pressure release if heart rate is
goes out of range 35～125bpm.
◆Automatic
pressure release if ECG electrodes fell down
during treatment.
◆Emergency
stop button. |
|
|
|
|
|
ECG
Amplifier |
|
Input
impedance: ≥4MΩ Maximum Augment
Gain：≥60dB Common mode rejection ratio（CMRR）:
≥90dB Minimum ECG detection voltage:
≤0.25mV |
|
|
|
|
Pulse Detection |
 |
|
Method：use Finger Plethysmograph Maximum
Augment：≥60dB（8 grades adjustable） |
|
|
|
NIBP
Measure |
|
NIBP required pressure range |
|
60～250mmHg（default
is 160 mmHg） |
|
NIBP measuring interval |
|
5～50mins（default
is 20mins） |
|
NIBP( high pressure) warning range |
|
upper limit:160～210mmHg（default is 200 mmHg） |
|
|
lower limit:0～120mmHg（default is 100 mmHg） |
|
NIBP (high pressure) Stop Treatment range |
|
Upper limit:210～230mmHg（default is 230 mmHg） |
|
|
Lower limit: 70～90mmHg（default is 90 mmHg） |
|
|
|
|
|
SPO2
Oxygen Saturation |
◆Oxygen
saturation range： 0 ～ 100﹪。
◆Oxygen
saturation warning range：50﹪ ～ 99﹪。
◆Accuracy
SpO2：± 1 digits for using the Finger Clip Sensor.
◆Oxygen
saturation is lower than warning value, the System
will alarm.
◆Oxygen
saturation is lower than 90%, record it into file.
◆Oxygen
saturation is lower than 80%, stop the compressor
automatically.
|
|
|
|
|
Triggering Method |
◆Internal
trigger：the System produce simulate square wave,
range from 10～170bpm
◆External
trigger：R-wave of patient ECG
◆External
trigger ratio: 1:1 or 1:2
◆ECG
trigger range： 35～125 bpm ±1 bpm |
|
|
|
|
Filter Technique |
|
Low-pass digital filter assorted with double T
filter eliminates 50/60Hz and high-frequency
interference, as well as 40Hz body muscle
electricity interference. |
|
|
|
|
Treatment Pressure Range |
 |
|
Adjustable from ：0～50kPa（classified in
20grades；2.5kPa /stage） |
|
|
|
Cuffs Inflation Method |
|
Three
classes sequence inflation from calves, low thighs
and upper thighs. |
|
|
|
Table Safe Working Load |
|
400
lb (180 kg) |
|
|
|
Treatment Timer |
|
Treatment Time setting range is 0～120 mins, the
default is 60 mins. |
|
|
|
System Protection |
|
The
circuit breaker: main fuse is
15A、computer system fuse is 3A. |
|
|
|
|
Continue Working Time |
|
More
than 8 hours per day in the regulate situation. |
|
|
|
|
Equipment Dimensions and Weight |
|
Length |
Width |
Height |
Net Weight |
|
2170mm |
930mm |
650mm |
265kg |
|
